555 Timer Tutorial: How It Works and Useful Example Circuits

In this 555 Timer tutorial, you’ll learn how to use the 555 timer to do fun things.

One of the first things many do with it is to create a blinking light. But that’s just one simple example of the many things you can do with this chip. You can also control motors, create an alarm, create a musical instrument, and much more.

Let’s start with an overview of the pins.

555 Timer Pinout

The circuit inside the 555 timer

Pin 1 Ground
This pin connects to the negative side of the battery.

Pin 2 Trigger
When this pin goes low (less than one-third of VCC), the output goes high.

Pin 3 Output
The output voltage from the chip is around 1.5 V lower than VCC when high and around 0 V when low. A 555 timer can give out only 100 to 200 mA in total. Check your chip’s datasheet for the exact value.

Pin 4 Reset
This pin resets the whole circuit. It’s an “inverted” pin, which means it resets when the pin goes low. This means the pin must be high normally so that the chip isn’t in a “reset” state.

Pin 5 Control Voltage
This pin is used to control the threshold voltage of the Threshold pin. This can be useful when you want to adjust the frequency of the circuit without changing the values of R1, R2, and C1. Sometimes you’ll see this pin connected with a capacitor (0.01 µF/10 nF) to ground; this is a way to keep any noise on it from influencing the frequency. Sometimes you’ll see it disconnected.

Note: I’ve heard from people not able to get their circuit working without this capacitor. So you can try adding a capacitor between this pin and ground if your circuit is not working.

Pin 6 Threshold
This pin sets the output back to low when the voltage goes high (above two-thirds of VCC).

Pin 7 Discharge
This pin is unconnected when output is high, and it’s connected to ground when output is low.

Pin 8 VCC Supply
This is the positive power supply pin and can take a voltage between 5 and 15 V.

To learn more about the circuit on the inside, check out the article How Does a 555 Timer Work?

Astable Mode

555 Timer in astable mode

When the 555 Timer is in astable mode it means that the output will never be stable. The output will keep switching between HIGH and LOW forever. That means it works as an oscillator.

You can use this to blink a light, create sound, control motors, and much more!

555 Timer Astable Circuit Example

Our first example is how to blink an LED with the 555 Timer. This is like the “hello world” equivalent of this IC.

555 Timer blinking LED circuit

Component List

This circuit is simple enough to build on a breadboard. To build it, you need the following components:

  • 9V Battery
  • 555 Timer IC
  • R1-R3: Resistor, 1 kΩ
  • LED1: Red 5mm LED or similar
  • C1: Capacitor, 1000 µF
  • C2: Capacitor, 10 nF (it usually works without this)

You don’t need exact values for the resistors and capacitors. But if you use the values listed above, your LED should blink about once every other second. Use the 555 Timer calculator to find the blinking frequency for other values.

Monostable Mode

555 Timer in monostable mode

Monostable means the output is stable in one state, and it will always come back to this state. You can push it out of that state, but it will always return back to its stable state after a certain time.

The output from the 555 Timer in monostable mode is normally LOW. When you trigger the circuit, the output goes HIGH for a certain amount of time before it goes back to LOW again.

This is sometimes called a one-shot circuit.

The time it stays HIGH is decided by the size of a resistor and a capacitor. The higher the values, the longer it stays HIGH.

If you connect a buzzer to the output, you can create an alarm circuit that is triggered for example by a window being opened.

555 Timer One-Shot Example Circuit

The following circuit turns on an LED when you push the button. After about 10 seconds, the LED turns off.

555 timer one shot circuit

Component List

  • 9V Battery
  • 555 Timer IC
  • R1: Resistor, 100 kΩ
  • R2: Resistor, 5kΩ to 1 MΩ (this is a pull-up resistor)
  • R3: Resistor, 1 kΩ
  • LED1: Red 5mm LED or similar
  • C1: Capacitor, 100 µF
  • C2: Capacitor, 10 nF
  • S1: Pushbutton, normally open

For longer delays, increase C1 and/or R1. If you want an adjustable delay, replace R1 with a potentiometer. Use the 555 Timer calculator to find the values you need.

The output is connected to control an LED, but could easily be modified to control a motor, a lamp, a coffee maker, or anything else. Just replace R3 and the LED with a transistor. See how in the section Driving Higher Loads below.

Bistable (Flip-Flop) Mode

Bistable means the output is stable in both states (HIGH and LOW). It will stay in one state until you push it over to the other state. Then it stays in the other state. You push it from one state to the other with the Trigger and Threshold pins.

This mode isn’t a timer function at all, and it’s not a common way to use the 555 Timer. In this mode, the 555 Timer works as a flip-flop.

You can for example use it to reverse the direction of a robot when it bumps into a wall. Or separate the ON and OFF switches for a machine.

555 Timer Bistable Example Circuit

The following example shows the 555 Timer in bistable mode. Here you have separate ON and OFF buttons to control an LED.

555 timer bistable flip-flop circuit

Component List

  • 9V Battery
  • 555 Timer IC
  • S1, S2: Pushbutton, normally open
  • R1, R2: Resistor, 5kΩ to 1 MΩ (these are pullup resistors)
  • Resistor (R3): 1 kΩ
  • LED: Red 5mm LED or similar
  • Capacitor (C1): 10 nF

The output is connected to control an LED, but could easily be modified to control a motor, a lamp, or anything else by connecting a transistor. See the section Driving Higher Loads below for examples.

555 Timer Output Current

The output of the 555 Timer can sink and source current of up to 200 mA.

Sourcing is when the output is HIGH and you’ve connected something from the output down to ground:

555 timer sourcing current

In the above circuit, the LED turns on when the output is HIGH.

Sinking is when the output is LOW and you’ve connected something from VCC to the output:

555 timer sinking current

In the above circuit, the LED turns on when the output is LOW.

If you use both sourcing and sinking in your circuit, you can make a cool emergency vehicle light effect by connecting two LEDs; a blue one that is sourcing current and a red one that is sinking current.

Or how about connecting two buzzers with different frequencies to create a siren?

Circuit Example: Police Car Emergency Lights

555 Timer circuit: Police car lights

Component List

  • 9V Battery
  • 555 Timer IC
  • R1-R2: Resistor, 1 kΩ
  • R3: Resistor, 470 Ω
  • R4: Resistor, 330 Ω
  • LED1: Red LED
  • LED2: Blue LED
  • C1: Capacitor, 1000 µF
  • C2: Capacitor, 10 nF (it usually works without this)

R1, R2, and C1 control the blinking speed. R3 and R4 set the brightness of the LEDs.

Driving Higher Loads

If you want to control motors, LED strips, or other things that need more than 200 mA of current, you can connect a transistor to the output.

If you want to use an NPN transistor, you’ll need to connect a resistor between the output and the base to limit the base current. 1 kΩ will probably work fine as a starting point.

555 Timer with BJT transistor on output
Driving higher loads from a 555 Timer with an NPN transistor

If you want to use a MOSFET on the output, make sure you use a MOSFET with a VGS that is lower than the output voltage from your 555 timer.

The resistor is there to protect the output pin from high spikes of current when the MOSFET is being turned on. But given that the 555 Timer supports 200 mA, it will most likely work without it in most cases.

555 Timer with MOSFET transistor on output
Driving higher loads from a 555 Timer with a MOSFET transistor

555 Timer Datasheet

Looking for the datasheet for the 555 timer? Each manufacturer has their own. Here’s a list of a few of the most common ones:

More 555 Timer Tutorials